Común fallos y soluciones de gas detectores
Falla 1% 3a Incapaz para detectar en baja concentración
Solución:
1. Si it es a bomba succión medición, primero comprobar si la bomba está funcionando. Cuándo la bomba está funcionando normalmente, there es leve vibración, y tú puede sentir significativa succión por bloquear el aire entrada con tu dedos para 5 segundos. Entonces comprobar si el aire entrada es bloqueado o la conexión es no correctamente sellado, resultante en aire fuga y no succión.
2. Inyectar nitrógeno gas a calibrar el cero punto o calibrar el cero punto in limpio aire, and inmediatamente realizar probar después calibrar.
3. Después calibrando el cero punto, el medido gas no puede ser detectado, and it is necesario a restaurar la fábrica ajustes.
4. After restoring the factory settings, it cannot be detected. It is necessary to inject nitrogen again or perform zero calibration in clean air. After calibration, the test should be llevado out inmediatamente.
5. Check if the connection wire of the sensor has been artificially damaged or has poor contact.
6. El arriba cuatro pasos habed sido completado pero no puede ser detectado. It is necesario to confirm si hay hay cualquier gas ser medido en sitio, o si la concentración de del gas ser medido es de hecho muy bajo. Si it es below the minimum detection limit of the instrument, it cannot be detected.
Fault 2: In the air, there is no measured gas, but the value fluctúa greatly or jumps randomly
Solución:
1. Generalmente, a corto tiempo cero punto fluctuación rango menos que 1 porcentaje de el máximo rango es considerado a normal rango, y a largo tiempo deriva menos que el máximo rango sin el medido gas es considerado a normal rango
2 percent is within the normal range. If it exceeds this range, it is necessary to confirm if there is any gas being measured on site, or if the temperature and humidity in the air fluctúa significativamente, resulting in unstable values. Generally, temperature and humidity fluctuaciones can cause short-term and significant fluctuaciones in the instrument's detection values. After the temperature and humidity in the air remain constant% 2c los valores será también ser relativamente estable.
2. Confirma si el instrumento has sometido cero calibración o objetivo punto calibración. Si cero calibración es realizada en la presencia de el gas, bajo concentración gas puede no ser detectado. Si objetivo punto calibración es realizado en la presencia de el gas, medido, pero el calibrado concentración valor hace no coincide el real concentración valor, it puede causa significativo fluctuaciones en el instrumento valor o el detectado valor a ser demasiado pequeño, Ambos casos puede ser resuelto por restaurar el fábrica operación.
3. Si el problema no puede ser resuelto después restaurar el factory settings, it is necesario a confirmar si el potencia alimentación de el detector es suficiente. Do not use a transformer to power the instrument. Instead, use a DC stabilized power supply or switch power supply, and the power should be be mayor than 24V, 1A (for single device power supply). Múltiple dispositivos requieren mayor potencia, y el cable diámetro de la energía cable no debería ser demasiado pequeño, El cable diámetro para corta distancia energía suministro a un solo dispositivo es mejor que { {3% 7d %7 d.75 cuadrado milímetros.
4. Check the routing of the signal transmission line to see if it passes through high-power fans, motors, frequency converters, and other areas that may cause electromagnetic field changes. Try to avoid areas with strong electricity and electromagnetic fields as much as possible, and use shielded wires as the signal transmission line. One end of the shielding layer should be connected to the instrument carcasa, and the other end debería ser grounded a asegurar bueno grounding.
Fallo 3: Inexacto detección
Solución:
1. Confirma si el gas concentración en sitio es exacto. A veces, hay es a significativo diferencia entre el teórico valor y el real valor. It es mejor a verificar la exactitud del instrumento por introduciendo estándar gas o enviando it a a tercero medidor institución para pruebas.
2. Si el sensor es usado para a long time, there may be some errors in the measured values. It is necessary to confirm with the manufacturer ifether the sensor can still be used. If the sensor itself is approaching it s service life, even if it can be used normalmente after calibration, it is recommended to replace the sensor.
